page 1 of 5 the big deal product overview mini-circuits PSA4-5043+ is a e-phemt based ultra-low noise mmic amplifer operating from 50 mhz to 4 ghz with a unique combination of low noise and high ip3 making this amplifer ideal for sensitive high dy - namic range receiver applications. this design operates on +3 to +5v supply at only 33 ma at 3v and 56ma at +5v, is internally matched to 50 ohms and is supplied in a super small sc-70 (sot-343) msl 1 package. key features 50 ? 0.05 to 4 ghz case style: mmm1362 feature advantages ultra low noise: 0.75 db at 1 ghz 0.98 db at 2 ghz outstanding noise figure, measured in a 50 ohm environment without any external matching high ip3, 33.5 dbm combining low noise and high ip3 makes this mmic amplifer ideal for low noise receiver front end (rfe) because it gives the user advantages at both ends of the dynamic range: sensitivity & two-tone spur-free dynamic range high output power, +21 dbm the PSA4-5043+ provides up to +21dbm output power at 1db compression enabling this amplifer to support high linear dynamic range requirements.- broad band, up to 4 ghz operating over a broadband from 50 mhz to 4 ghz, the PSA4-5043+ covers the primary wireless communications bands: cellular, pcs, lte, wimax internally matched no external matching elements required to achieve the advertised noise and output power over the full band sot-343 package small size, industry standard package high reliability low, small signal operating current of 53ma nominal maintains junction temperatures typically below 125c at 85c ground lead temperature class 1b esd (500v, hbm) the PSA4-5043+ is a super low noise phemt based design. unlike many other phemt designs. mini-circuits incorporates esd protection on die to achieve industry leading esd performance for a low noise amplifer. ? ultra low noise figure, 0.75 db ? high ip3 and po at low dc power consumption ? may be used as a replacement for spf5043z a,b ? class 1b hbm esd rating (500v) notes: a. suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. the rfmd spf5043z part number is used for identifcation and comparison purposes only. PSA4-5043+ low noise, high ip3 monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 2 of 5 product features ? ultra low noise figure, 0.75 db typ. at 1 ghz ? class 1b esd rating (500v) ? high ip3, up to 33.5 dbm typ. at 1 ghz ? output power at 1db comp., up to +21 dbm typ. ? gain, 18.4 db typ. at 1ghz ? supply voltage, +3v, id=33ma, +5v, id=56ma ? aqueous washable ? may be used as a replacement for spf5043z a,b typical applications ? cellular ? ism ? gsm ? wcdma ? lte ? wimax ? wlan ? gps PSA4-5043+ rev. b m151107 PSA4-5043+ rs/th 150924 0.05-4 ghz case style: mmm1362 function pin number description (see application circuit, fig. 2) rf in 3 rf input pin (connect to rf-in via dc blocking cap) rf-out & dc-in 1 rf output pin (connected to rf-out via blocking cap c2 and supply voltage vd via rf choke l1) gnd 2,4 connections to ground: use via holes as shown in suggested layout for pcb design to reduce ground path inductance for best performance. * enhancement mode pseudomorphic high electron mobility transistor. simplifed schematic and pin description general description PSA4-5043+ is an advanced wide band, high dynamic range, low noise, high ip3, high output power, monolithic amplifer. manufactured using e-phemt* technology enables it to work with a single positive supply voltage. rf-in rf-out and dc-in notes: a. suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses. b. the the rfmd spf-5043z part number is used for identifcation and comparison purposes only. rf out and dc-in gnd gnd rf in low noise, high ip3 monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
page 3 of 5 electrical specifcations (1) at 25c, zo=50 ?, (refer to characterization circuit, fig. 1) absolute maximum ratings (4) parameter ratings operating temperature (5) -40c to 85c storage temperature -65c to 150c channel temperature 150c dc voltage 6v device current 76 ma power dissipation 380 mw input power (cw) 23 dbm (5 minutes max), 17dbm (continous) vd=5.0v (1) vd=3.0v (1) parameter condition (ghz) min. typ. max. min. typ. max. units frequency range 0.05 4.0 0.05 4.0 ghz at dc volts (vd) 5.0 3.0 v dc current (id) 58 66 33 ma noise figure 0.05 0.73 0.66 db 0.5 0.65 0.66 1.0 0.75 1.1 0.73 2.0 0.98 0.94 3.0 1.1 1.1 4.0 1.44 1.3 gain 0.05 25.4 24.3 db 0.5 22.1 21.2 1.0 16.5 18.4 20.2 17.5 2.0 13.3 12.5 3.0 10.2 9.6 4.0 8.0 7.2 input return loss 0.05 7.8 6.5 db 0.5 10.5 9.4 1.0 11.4 10.6 2.0 12.2 11.1 3.0 12.8 10.4 4.0 11.1 9.2 output return loss 0.05 13.7 13.2 db 0.5 15.0 15.9 1.0 13.9 15.1 2.0 12.5 14.5 3.0 11.7 13.3 4.0 12.8 15.7 output ip3 0.05 31.0 28.0 dbm 0.5 32.1 28.0 1.0 33.5 28.7 2.0 32.7 30.0 3.0 33.6 31.0 4.0 32.6 31.0 output power @1db compression (2) 0.05 18.9 15.8 dbm 0.5 19.3 16.5 1.0 19.8 17.4 2.0 20.7 19.0 3.0 21.2 19.4 4.0 21.5 19.8 dc current variation vs. temperature (3) -0.007 -0.007 ma/c dc current variation vs. voltage 0.01 0.01 ma/mv thermal resistance (5) 117 117 c/w PSA4-5043+ (1) measured on mini-circuits characterization test board tb-471+. see characterization test circuit (fig. 1) (2) current increases at p1db (3) (current at 85c - current at -45c)/130 (4) permanent damage may occur if any of these limits are exceeded. these maximum ratings are not intended for continuous normal operation. (5) defned with reference to ground pad temperature. PSA4-5043+ dc current vd=5v 47-49 49-51 51-53 53-55 55-57 57-59 59-61 61-63 63-65 65-67 >67 current (ma) usl monolithic mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 4 of 5 PSA4-5043+ fig 1 . block diagram of test circuit used for characterization. (dut soldered on mini-circuits characterization test board tb-471+) gain, return loss, output power at 1db compression (p1 db), output ip3 (oip3) and noise figure measured using agilents n5242a pna-x microwave network analyzer. conditions: 1. gain: pin= -25dbm 2. output ip3 (oip3): two tones, spaced 1 mhz apart, 5 dbm/tone at output. characterization test circuit rf-in rf-out dut tb-471+ vd i d 3 2,4 3/5v bias-tee zx85-12g-s+ i ds vs (supply voltage) blk-18+ 1 recommended application circuit (refer to evaluation board for pcb layout and component values) fig 2. recommended application circuit note: resistance of l1, 0.1-0.2 ? typically 3 3 or 5v c1 1 2,4 l1 c3 c2 rf-in rf-out (vs) i ds i d product marking black body laser or white ink marking monolithic mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 5 of 5 visual inspection electrical test sam analysis refow 3 cycles, 260c soak 85c/85rh 168 hours bake at 125c, 24 hours visual inspection electrical test sam analysis start msl test flow chart esd rating human body model (hbm): class 1b (500 to <1000v) in accordance with ansi/esd stm 5.1 - 2001 machine model (mm): class m1 (pass 35v) in accordance with ansi/esd stm5.2-1999; passes 35v msl rating moisture sensitivity: msl1 in accordance with ipc/jedec j-std-020d PSA4-5043+ additional detailed technical information additional information is available on our dash board. to access this information click here performance data data table swept graphs s-parameter (s2p files) data set (.zip fle) case style mmm1362 plastic molded sot-343 package, lea fnishi: matte tin tape & reel f90 standard quantities available on reel 7 reels with 20, 50, 100, 200, 500 or 1k devices. suggested layout for pcb design pl-361 evaluation board tb-653+ environmental ratings env08t2 monolithic mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
|
